I've started a how-to on setting up an OBi202 to work directly with Anveo Direct, bits and pieces can be found, but not all in one place.. Different forums, websites, and then the manual..
I have my OBi202 on it's own static IP, but would work if you were using your OBi202 as a router, for dynamic IPs, would need to log into AnveoDirect and change the IPs if/when your IP changes. Port Forwarding may come later for putting the ATA behind a router, but not a priority for me right now.
Keep in mind I am setting it up for a 2-Line fax machine, but this should only matter for the CODEC page and the Anveo Outbound Call Routing
Variables - You will want to edit these for your numbers
15556667777 - Also set as outgoing CID and CNAM
15556668888
123.125.25.156 - OBi202's static IP
AnveoDirect Trunk Prefix Code - 012345 (Alpha is ok too)
Using OBiTALK's web interface, non-default changes are mentioned
Anveo Direct 1. In normal settings Set Admin Password SP1 Settings-Gear OBiTALK Compatible Service Providers Generic Service Provider Configuration Name Anveo Direct Primary Line for Outgoing Calls - Check Both Incoming Calls Will Ring On - Line1 VoiceMail Notification - Uncheck Both Service Provider Proxy Server sbc.anveo.com Username obi202 (LOWERCASE) 2. Obi Expert 3. Voice Services Gateways & Trunk Groups Voice Gateway1 Name Anveo Direct Access Number sp1(sbc.anveo.com;ui=15556667777) Digit Map (<012345>1xxxxxxxxxx|<011:012345>xx.) AuthUserID 15556667777 4. Voice Services SP1 Service X_InboundCallRoute ph X_RegisterEnable - Uncheck X_UserAgentPort 33445 CallForwardOnBusyEnable - Check CallForwardOnBusyNumber ph2 5. Service Providers ITSP Profile A General Name Anveo Direct X_SymmetricRTPEnable - Check ITSP Profile A SIP ProxyServer SBC.ANVEO.COM OutboundProxy SBC.ANVEO.COM 6. Codecs CODEC Profile A G729 Codec Enable - Uncheck G726R32 Codec Enable - Uncheck FAX Event Enable - Check Codec Settings T38ECM - Check 7. Physical Interfaces PHONE 1 OutboundCallRoute {(Mvg1):vg1} CallWaitingEnable - Uncheck ForwardOnBusyNumber ph2 PHONE 2 OutboundCallRoute {(Mvg1):vg1} CallWaitingEnable - Uncheck
For incoming calls, I want them to ring Phone1, if Phone1 is busy, then ring Phone2, if Phone1 and Phone2 are busy, give a busy tone
Anveo Settings
Destination SIP Trunks
Title OBi202SIP URI obi202@123.125.25.156:33445
Outbound Services/Call Termination
Dialing Prefix: 012345Authorized IP Addresses: 123.125.25.156Call Routing Method: Custom Least Cost Routing ModelGet Routes/Carriers within 'Rate Cap' from: Custom Routes At the bottom check all carriers with T.38, US/Canada and WorldwideThen take top N results: 5 Routes/CarriersFinally send calls (with failover) to routes in order of: random orderSmart Route Option: - Checked
Changing the Routes/Carriers is from a suggestion by Anveo's support, Thanks!
I think this is everything I have set.. As long as the SIP Scanners don't find the UserPort, all should be good. Even if they do find it, in this case, it is my fax machine, so I won't hear it anyways.
Outstanding Tweaks:
Inbound Calls,
There is a way to enter the DIDs, so the incoming Route pays attention to the DIDs, but I could not figure it out, was initially why it wasn't working.. :|
Outbound Calls,
Have to add dialing in E164 format outside US/Canada.. Also add input checking, right now 1NPANXXXXXX works without checking for the proper NPANXX (10001005555 is accepted), and 011+ works, but dialing 44.. does not.
↧